Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.09.13 

API Toolbox 

Bug Fixes 

1. Fixed the following issues with tabs in API Toolbox:

   1. Closing a tab when there are already more than 5 on the dashboard was not working properly.

   2. Users in API 570 would incorrectly receive a pop-up stating their CML application was already open after re-opening the application. 

Hydrotest PowerTool 

Bug Fixes 

1. Fixed an issue in Hydrotest PowerTool where Temperature Derating Factor on Gas analyses was not displayed properly (TT-11506). 

PLTB 

Bug Fixes

1. Fixed an issue in the following Design & Stress applications where the Net Longitudinal Stress value was not calculated with 75% per the newest revision of B31.4 (TT-11549). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.08.30 

AC Mitigation PowerTool 

Enhancements 

1. Input validations have been added to AC Mitigation Steady State to instruct the user to recalculate their sections when a user adds or deletes powerlines or pipelines to their case. 

Bug Fixes 

1. Fixed an issue in AC Mitigation Steady State where creating a new section would overwrite all sections with the mitigation of the first one (TT-11519). 

HUB Platform 

Bug Fixes 

1. Fixed an issue where users were unable to assign a date to cases (TT-11538). 

PLTB 

Enhancements 

1. The Surge Analysis – Water Hammer application has been updated to allow users to add results tables and plots for Node Pressures and Flow Rates to the report (TT-11188). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.08.23 

AC Mitigation PowerTool 

Bug Fixes 

1. Fixed the following issues in AC Mitigation PowerTool – Steady State application:

   1. The bond table in the Mitigation tab would not allow a user to scroll through (TT-517)

   2. Calculations could not complete for sections that did not intersect Powerlines or Pipelines (TT-11527) 

PLTB 

Bug Fixes 

1. Fixed an issue in calculations for API 1102 Railroads applications where k_mu reference was not properly accounted for in Stiffness Factor for Earth Load Circumferential Stress  (TT-11473). 

2. Fixed an issue in Maximum Allowable Pipe Span Length where Youngs Modulus of Elasticity was not converting to Metric units properly (TT-11164). 

Map 

Bug Fixes 

1. Fixed an issue in the ESRI Map application where the satellite/terrain toggle button would disappear after importing an entity (TT-11313). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.08.16 

API Toolbox 

Enhancements 

1. Module API 570 in API Inspectors Toolbox have been updated to allow users to undo LT/ST analyses. 

PLTB 

Bug Fixes 

1. Fixed an issue in calculations for API 1102 Highway applications where k_mu reference was not properly accounted for in Stiffness Factor for Earth Load Circumferential Stress  (TT-11473). 

PRCI OBS 

Bug Fixes 

1. Fixed an issue in Level 2 calculations where Water Depth was incorrectly flagged for input validation when an existing case was calculated (TT-11491). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.08.09 

API Toolbox 

Enhancements 

1. The notification for shared cases now contains information on Modules to which the shared reports belong to 

PLTB 

Enhancements 

1. Purging Calculations within the Testing module has been updated to include the following (TT-11392): 

   1. Added fluid directive for user to select different fluid types 

   2. Calculation was updated to use the specific gravity of the fluid selected 

   3. Custom blow-off sizes 

   4. Custom blow-off coefficients 

   5. The associated report(s) have been updated 

Bug Fixes 

1. Fixed an issue AGRA & GRPA > Accidental Release through a small pipeline where the flow rate was not being calculated properly (TT-11452). 

2. Fixed an issue in API 1102 Pipeline Highway applications where the friction force coefficient was not changing properly with change of Soil Type (TT-11473). 

PRCI OBS 

Bug Fixes 

1. Fixed an issue in Level 2 calculations where the Sigma A and B coefficients were unable to be updated when JONSWAP was selected for Spectral Setting (TT-11491).

AC Mitigation 

Bug Fixes 

1. Fixed an issue where the distributed anode ground from the first section gets copied over to other sections where mitigation is applied (TT-11482).

2. Fixed an issue related to pipeline and powerline data changing after mitigation and calculation (TT-11032).

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.08.02 

HDD PowerTool   

Enhancements 

1. Google Maps and GIS functionality has been consolidated into one application for all applications, where users build a borehole profile using ESRI Map.

API Toolbox 

Enhancements 

1. Uploaded photos now have editable names in the Appendix 

2. API 653 now has the ability to add user defined tmins 

3. API 570 now highlights the governing component in the Component Remaining Life report.  

4. CML template modified to include LT/ST changes 

Bug Fixes 

1. Fixed an issue in API 653 where label changes to the Roof and Floor labels were not being properly updated in the Appendix A, CML page (TT-11468). 

AC Mitigation PowerTool 

Bug Fixes 

1. Fixed an issue where section data was incorrectly shown for all sections after the first one (TT-11470). 

PLTB 

Enhancements 

1. Reports now show the Pipe Regulatory Code chosen by a user for analysis where applicable. 

Bug Fixes 

1. Fixed an issue AGRA & GRPA > Accidental Release through a small pipeline where the flow rate was not being calculated properly (TT-11452). 

2. Fixed an issue in API 1102 Pipeline Highway applications where the friction force coefficient was not changing properly with change of Soil Type (TT-11473). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.07.19 

API Toolbox   

Enhancements 

1. The following enhancements have been added to the API 570 module:

   1. Ability to add user defined tmins.

   2. Enhanced calc to calculate remaining life based on LT and ST corrosion rates and modified the report to include it. 

Hydrotest PowerTool   

Enhancements 

1. Added new input parameter called ‘Test Pressure Factor’ for cases that are in line with B31.8/B31.4 for gas and liquid. 

Crossings Workflow 

Bug Fixes 

1. Fixed an issue where the ‘Soil Type’ drop-down was changing values after clicking ‘Calculate’ (TT-11434).  

ESRI Map 

Bug Fixes 

1. Fixed an issue in the ESRI Map application where reopening a mapping to an entity in the import screen was clearing the screen (TT-10979). 

PRCI OBS 

Bug Fixes 

1. Fixed an issue in Level 2 Batch Run where ‘Water Depth’ was able to be added to your batch (TT-11439). 

2. Fixed issue for license related access for Level 1 and Level 2 (TT-11442). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.07.12 

API Toolbox   

Enhancements 

1. The following changes have been done to API 510: 

   1. SH has been removed from the logic of the SH and Head calculation applications 

   2. Users are now able to disable Chamber 2 in the Final Report Builder application from going to the report if not applicable to the inspection. 

2. The API 570 Final Report Builder application has been updated to allow users to choose the tmin values based on the piping material (CS) and (SS). 

3. Users have been provided an option in all 3 modules (653, 510, 570) to skip printing appendix pages to final report 

ESRI Map 

Bug Fixes 

1. Fixed an issue in the ESRI Map application where .kmz/.kml/.gdb were unable to be imported if there were special characters in the entity’s name from Google Maps or arcGIS (TT-11313).

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.07.05 

API Toolbox   

Enhancements 

1. A new pipe insulation type ‘Uninsulated’ has been added to the API 570 Final Report Builder. 

Bug Fixes 

1. Fixed an issue in API 570 where users were unable to create a new report in the ASME VIII application. 

AC Mitigation PowerTool   

Enhancements 

1. Fault Current applications’ faulted node visualization has been replaced with a highlighting of the powerline over the section where the fault occurs (TT-11345). 

HDD PowerTool 

Bug Fixes 

1. Fixed an issue in HDD PowerTool > Steel Pipe applications where Reduced Wall Thickness checkbox was not saving to the case.  

PLTB 

Bug Fixes 

1. Fixed an issue in HDD Lite > Steel Pipe applications where Reduced Wall Thickness checkbox was not saving to the case. 

2. Fixed an issue in API 1117 – Movement of In-Service Pipeline applications where Pipe Design Factor was not saving to the case.  

3. Fixed an issue in CEPA Wheel Load Analysis where the Impact Factor was incorrectly overwritten with the interpolated value if the ‘Pavement Type’ was set to ‘User Defined’. 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.06.28

API Toolbox   

Enhancements 

1. Users are now able to transfer ownership of reports in API 653, 510, and 570 modules:

   • Users can request ownership of reports owned by another user provided they are shared with the user requesting ownership

   • Users who transfer ownership of a report to another can view the transferred report but no longer make edits 

2. The following modifications have been made to API 510:

   • The CML page report has been updated with grid lines to improve readability

   • A new pressure field ‘MAEWP’ has been added to the Report Builder main page 

AC Mitigation PowerTool   

Enhancements 

1. Cases now have a new checkbox called ‘Disable Mitigation’ that allows users to toggle mitigation on/off on their cases without having to delete/re-do mitigation (TT-11218). 

2. The Fault Current application now populates a powerline name if any when selecting from the list of powerlines configured (TT-11375). 

3. Users can now save their graph settings as part of their case data (TT-11258).

   1. When the case is loaded up again, the graph settings set before saving are now retained. 

Bug Fixes 

1. Fixed an issue where individual plots for induced current and voltages were not included in the report (TT-11403, TT-11142). 

2. Fixed an issue where the unmitigated plot was showing the mitigated plot in the reports (TT-11407). 

3. Fixed an issue where the section lines wouldn't show up in the overview (sections tab) when calculate of angles and distances was clicked once and the results wouldn't update in the plot when calculate for the analysis was clicked. However, both sections and results showed up on the second click (TT-11364).  

HDD PowerTool 

Bug Fixes 

1. Fixed an issue in HDD PowerTool Steel applications where failure indicators on stress calculations were incorrectly highlighted (TT-11404).  

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.06.21  

AC Mitigation PowerTool   

Enhancements  

1. The following modifications have been made to the AC Mitigation PowerTool applications:

   • The Induced Current and Current Density columns in the results plot have been switched to make easier interpretation of Current Density results. 

   • The reference line used by a user for calculating sections is now saved for a user’s cases. 

   • The Powerline section of the Steady State application’s report has been updated to offer better user experience on viewing data. 

Bug Fixes  

1. Fixed an issue where users with more than 20 sections would see their scrollbar disappear in the Section Lines sub-tab (TT-11364). 

Hydrotest PowerTool 

Enhancements 

1. The Hydrotest PowerTool has been updated with pipe regulatory codes for CSA Z662 in addition to the existing B31.4 and B31.8 codes.  

   1. This includes catalog changes for: 

      • Design class and Location factor

      • Joint type and Joint factor

      • Temperature derating factor

In addition to the above, Low Vapor Pressure and High Vapor Pressure, Fluid Type were added and Test Pressure Factor. 

PTLB 

Bug Fixes 

1. Fixed an error in the following Design & Stress Analysis applications where using Reduced Wall Thickness would apply an incorrect unit conversion (TT-11367, TT-11377).

   • Design Pressure

   • Maximum Allowable Pipe Span Length 

2. Fixed an error in Regulator & Station Piping Sizing application where the report wouldn't generate (TT-11389). 

API Toolbox   

Bug Fixes

1. Aspect ratio applied to images uploaded on base page of Report Builder to show images correctly with reduced size. This is done for 510, 653 and 570 modules. 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.06.14  

API Toolbox   

Enhancements  

1. Users are now able to edit/rename their reports in the 653/510/570 Final Report Builders. 

2. New Construction Codes of API-12C and API-12F have been added to the API 653 Final Report Builder. 

ESRI Maps

Bug Fixes 

• Fixed an issue in the ESRI Maps application where users were not able to manually draw features (pipelines, powerlines) or import kml/kmz data files(TT-11349). 

AC Mitigation   

Bug Fixes 

1. Fixed an error in Fault Current where the individual plots were missing some plots and legends (TT-11355). 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.05.31

HUB Platform  

Bug Fixes  

1. Fixed an issue where the hierarchy panel would disappear after 20 seconds when HDD Borehole Stability calculation was opened (TT-11317). 

AC Mitigation

Bug Fixes 

1. Fixed an issue related to the decimal digit being restricted to two decimals and not to the configuration of the measurable property associated for the pipeline tab and sections tab (TT-11322). 

2. Fixed an issue where the cases were not being saved with a project name (TT-11274). 

3. Fixed an issue related to adding new section lines via ESRI map would have default resistivity data and would not get the data from the section line above. 

4. Fixed an issue for calculating sections lines in ESRI (TT-11050).

API Toolbox 

Bug Fixes  

1. Issue got fixed for API  510 for sections if left blank will add section headers as section data in write up upon import 

2. Issue fixed in API 570 for import process with no CML data bringing in blank checklist, losing data from checklist. 

3. API 510, corrected the tmin logic on nozzle evaluation. 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2024.05.24  

PLTB  

Enhancements  

1. Compressor Station Piping – Pipe Wall Thickness calculation with Pipeline Compressor (PLTB -G), Pump Station Piping – Pipe Wall Thickness calculation in Pipeline Pump (PLTB – L) and Regulator & Station Piping Sizing calculation within Regulators & Meters (PLTB -G) have all been updated with pipe regulatory codes for CSA Z662, in addition to the existing B31.4 and B31.8 codes. These include catalog changes for design class and location factor, joint type and joint factor, and temperature derating factor.  

Bug Fixes  

1. Fixed an issue in Maximum Pipe Span Length calculation of Design & Stress Analysis where the validation message for operating pressure does not account for the unit of pressure, and instead just evaluates the number inputted into the calculator against the limit (TT-11254). 

AC Mitigation  

Enhancements  

1. Released new pdf report template in the Steady State application for a better user experience. 

Bug Fixes 

1. Fixed an issue related to mitigation data not appearing in the UI when changes were updated to the case data (TT-11329). 

2. Fixed an issue where importing an excel file with 0 in shield wire or phase wire data would save as blanks (TT-11268). 

3. Fixed an issue in the steady state calculation where the pipe names could not be saved with blanks or with special characters (TT-11002). 

HDD PT  

Bug Fixes  

1. Fixed an issue with Drilling Fluids and Mud Management where the reports were not rounding dec digits in metric unit set (TT-11281).  

2. Fixed an issue in the Installation and Stress Analysis – Vertical calculation where input data would get cleared when measured depth was saved with 0 value (TT-11264). 

3. Fixed an issue with importing elevation profile always imports the distance as feet, regardless of the unit set selected (11249). 

4. Fixed an issue where the reports were generating without the additional attached pdf’s (TT-11210).  

API Toolbox 

Bug Fixes  

1. Issue fixed for checklist data not showing up upon import if CML has no data in template while importing 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.04.05 

AC Mitigation 

Bug Fixes 

1. The following issues were fixed in the AC Mitigation PowerTool Steady State applications: 

   1. A scroll bar was added on the drop-down menu for map section where user’s sections, powerlines, etc. are stored (TT-11413).

   2. Distribution anode was incorrectly being deleted for a segment if parallel mitigation was removed (TT-11051).

   3. Fixed an error where the unmitigated results were incorrectly displaying mitigated results when parallel mitigation was true with 0 resistance (TT-11115).

API Toolbox 

Bug Fixes 

1. Fixed an issue in the 653 Report Builder where the final report was not generating unless the user had entered in data in the Internal Notes section (TT-11187, TT-11194). 

PRCI RSTRENG 

Enhancements 

1. The decimal precision of wall thickness in the report has been updated to 4 decimal places in line with industry standards (TT-11101). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.03.29 

PLTB 

Enhancements 

1. New UI updates for Pipeline Pumps application to enhance the appearance and usability of the application. 

2. New UI updates for input validations, required fields, warning and error messages for Polyethylene Pipes (Gas & Liquid) to enhance usability and intuitiveness. 

Bug Fixes 

1. Fixed an issue in Hydraulics (batch run) where a warning message was displayed in the excel results to repair the excel (TT-11158). 

API Toolbox 

Enhancements 

1. API 653 Report Writeup has a new section to add internal notes for reference that will not go to the report. 

Bug Fixes 

1. Fixed an issue in API 1102 applications where the validation for the ratio of Wall Thickness to Outside Diameter was being incorrectly calculated (TT-11147). 

AC Mitigation 

Enhancements 

1. Released new feature where a warning message is displayed to the user when a section line is crossing the same powerline or pipeline more than once in Steady State calculation (TT-11138).  

PRCI OBS 

Bug Fixes 

1. Fixed an issue in the level 3 pipe calculator section where the results in metric unit set were incorrect for ‘in air weight’ and ‘submerged weight’ (TT-11096). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.03.15 

PLTB 

Enhancements 

1. New UI updates for Pipeline Corrosion applications to enhance the appearance and usability of the application. 

2. CEPA applications in Pipeline Crossings now support a Metric unit set that is used in the standard CEPA calculations. 

HDD PowerTool 

Bug Fixes 

1. Fixed an issue where Plastic Pipe applications were not loading saved data (TT-11135, TT-11141, TT-11143). 

API Toolbox 

Enhancements 

1. Users in all API Toolbox modules are now able to share their cases with users outside of their company 

AC Mitigation 

Enhancements 

1. Released new feature which gives the user the ability to now import mitigation data via an excel file similar to section line import in the Steady State Application 

Bug Fixes 

1. The following issues have been fixes in AC Mitigation applications:

   1. The list of sections in the Mitigation tab were not condensed inside Section box (TT-11017).

      1. This menu was missing a scroll bar

   2. Distributed anode in the Mitigation tab was incorrectly deleted when a user clicked on that field (TT-11051). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.03.8 

PLTB 

Enhancements 

1. New UI updates for the following modules to enhance the appearance and usability of the application:

   1. AGR & GPRA

   2. ALR

   3. Pipe Blast Gas and Liquid 

HDD PowerTool 

Enhancements 

1. Released a new calculation model in the Hydraulic Fracture Analysis application that now includes Average Delfts model (Average Soil Layer).

   • This considers the stress caused by soil layers above the layer in contact with the bore profile for Hydraulic Fracture Analysis. 

2. Released Sensitivity Analysis study (Manual and Automated) for Polyethylene Pipe – Pull Force & Installation Stresses  

API Toolbox 

Enhancements 

1. Improvement made on the Appendix page loading to cause it not to fluctuate during report generation process. 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.02.16 

PLTB 

Bug Fixes 

1. Fixed an issue in PLTB applications where images uploaded to a case would not show in the printed report (TT-10942). 

Crossings Workflow 

Bug Fixes 

1. Fixed an issue where images uploaded to a case would not show in the printed report (TT-10994). 

HDD PowerTool 

Bug Fixes 

1. Fixed an issue for GIS applications where Pipe Entry and Pipe Exit were not calculating (TT-10976). 

API Toolbox 

Bug Fixes 

1. Fixed an issue where the Component TML Record would hang up loading after importing 200 + records (TT-11035). 

PRCI RSTRENG 

Bug Fixes 

1. Fixed an issue where calculations in Metric were incorrect due to an improper unit conversion on the profile pit data (TT-11056). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2024.01.05 

API Toolbox 

Enhancements 

1. Added a refresh button in the 510 module’s Report Appendix B calculations for shell and head calc, that will pull updated information from base page to these calcs pages.

PLTB 

Enhancements 

1. New UI look update for Design & Stress Analysis Gas and Liquid modules to enhance the appearance and usability of the applications. 

Bug Fixes 

1. Fixed an issue in Parallel Line Explosive Charge applications where users would be incorrectly blocked on calculation if they changed their units (TT-10835). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2023.12.27 

AC Mitigation 

Bug Fixes 

1. Fixed an issue where the case did not execute once the case was imported and saved  

Enhancements 

1. Released new look and feel for the user interface of the Fault Current application while updating user experience of existing features. 

HDD PowerTool 

Bug Fixes 

1. Fixed an error where the borehole profile was being represented incorrectly in the plot when the section was configured as straight and level 

Hydrotest PowerTool 

Bug Fixes 

1. Fixed an error where the configured sections of the pipeline were not displayed in the map 

API Toolbox 

Bug Fixes 

1. The following issues were fixed in API Toolbox: 

2. In API 653, the location dropdown would open when new record was created 

3. In API 653 Nozzle, the dropdown value would change to the value that was typed in for searching and filtering 

4. In API 570 Report Builder, renamed circuit ID to description  

5. In Asset, added edit button for Tank and Vessel to match what Pipe has 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2023.12.25 

API Toolbox 

Bug Fixes 

The following issues were fixed in API Toolbox: 

1. Improved performance for 510 Report Builder where loading was time excessive 

2. In API 570 remaining life page, the sch dropdown value would change to the value that was typed in for searching and filtering 

3. In API 570 CML, the size dropdown value would change to the value that was typed in for searching and filtering 

4. In API 510 CML, the size dropdown value would change to the value that was typed in for searching and filtering 

5. In 510 shell calculations (app A), improved performance when saving was taking a long time while displaying “loading please wait” spinner 

6. In API 510 CML, the first-row data was getting erased when entered manually 

7. In API 510 app A, user was not able to input ‘t act’ values  

8. In API 653, removed blank rows/cells in the tables that did not contain any data for both Word and PDF reports 

9. In Asset, the critical sections were getting erased after editing any values 

10. In Asset, the MOV report was not generating  

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2023.12.20 

HUB Platform 

Enhancements 

Released the following updated tab feature: 

1. The tabs do not wrap to multiple rows 

2. Calculation name is displayed as a tooltip when hovered over the tab 

3. 6+ tabs get stacked in a dropdown for easy access to the last tab (tab 5) 

4. Streamlined opening and closing of tabs   

AC Mitigation 

Enhancements 

1. Released new look and feel for the user interface of the Steady State application while updating user experience of existing features. 

API Toolbox 

Bug Fixes 

1. The following issues were fixed in API Toolbox: 

2. API 653 module users were unable to scroll through the records of the AST Nozzle Calculation application (TT-10737). 

3. In API 510 module’s Report Head module, the tmin for Head 3 was not populating based on information provided on base report builder page and in head calculation  (TT-10537). 

HDD 

Bug Fixes 

1. Fixed an issue in HDD PowerTool where straight level sections were not having their angle and measured lengths shown in the report (TT-10758). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2023.12.15 

API Toolbox 

Bug Fixes 

1. Fixed an issue where signatures were not getting uploaded into the Final Report Builder for each associated module (TT-10857). 

HDD 

Bug Fixes 

1. Fixed an issue in HDD PowerTool where applications with sections defined by the user were not saving when edited (TT-10812). 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2023.10.20

HUB Platform

Enhancements

1. Released AutoCAD import within DB Import to create a borehole profile that can be repurposed in HDD PowerTool for the calculations listed below 

2.  Cables in Conduits 

   1. Installation of Cables in Conduits and Pipes - Google Map 

   2. Installation of Cables in Conduits and Pipes - GIS 

3. Polyethylene Pipe 

   1. Pull Force & Installation Stresses (Specific Radius of Curvature) - Google Map 

   2. Pull Force & Installation Stresses (Specific Radius of Curvature) - GIS 

4. Steel Pipe 

   1. Pull Force & Installation Stresses - Vertical - Google Map 

   2. Pull Force & Installation Stresses - Vertical & Horizontal Plane 

   3. Pull Force & Installation Stresses - Vertical GIS 

   4. Pull Force & Installation Stresses - Vertical and Horizontal GIS 

API Toolbox

1. CML performance improved for all three modules API 653, API 570 and API 510 PRCI OBS (On-Bottom Stability)

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2023.01.16

API Toolbox

API 653

Bug Fixes

1. Fixed an issue in Shell Settlement where the graph would appear inverted after saving a case.

PLTB- 

Enhancements

1. Added a ‘User Defined’ option to ‘Pavement Type’ in all CEPA crossings calculations that allows a user to input an Impact Factor of their choice. This applies to:

   • CEPA Track Load Analysis (Gas)

   • CEPA Wheel Load Analysis (Gas)

   • CEPA Grid Load Analysis (Gas)

Bug Fixes

1. Fixed an issue in API 1102 Pipeline Crossing Railroad and Highway Gas where the unit of measure for an input was not being considered in input validations.

   • E.g. A user would select Outside Diameter of 12.75 inch and Wall Thickness of 7.925 mm (.312 inch). The input validation for Wall Thickness/Outside Diameter being between 0.01 and 0.08 would incorrectly be calculated as 0.498 and the user would be prevented from running the calculation.

2. Fixed the following issues in Cathodic Protection reports:

   • Values and units of were not being wrapped on the same row.

   • Power Consumption of Cathodic Protection Rectifier (Gas) data points with ‘KWH’ were being displayed inconsistent from the widget UI.

   • Rudenbergs Formula For the Placement of an Anode Ground Bed (Gas) was displaying an extra row after the widget title in the report.

PLTB-L

Enhancements

1. Added a ‘User Defined’ option to ‘Pavement Type’ in all CEPA crossings calculations that allows a user to input an Impact Factor of their choice. This applies to:

   • CEPA Track Load Analysis (Liquid)

   • CEPA Wheel Load Analysis (Liquid)

   • CEPA Grid Load Analysis (Liquid)

Bug Fixes

1. Fixed an issue in API 1102 Pipeline Crossing Railroad and Highway Liquid where the unit of measure for an input was not being considered in input validations.

   • E.g. A user would select Outside Diameter of 12.75 inch and Wall Thickness of 7.925 mm (.312 inch). The input validation for Wall Thickness/Outside Diameter being between 0.01 and 0.08 would incorrectly be calculated as 0.498 and the user would be prevented from running the calculation.

2. Fixed the following issues in Cathodic Protection reports:

   • Values and units of were not being wrapped on the same row.

   • Power Consumption of Cathodic Protection Rectifier (Liquid) data points with ‘KWH’ were being displayed inconsistent from the widget UI.

   • Rudenbergs Formula For the Placement of an Anode Ground Bed (Liquid) was displaying an extra row after the widget title in the report.

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2022.12.16  

API Toolbox 

API 653 

Bug Fixes 

1. Fixed an issue in Report Config Appendix 653 where there was an extra MRT calculations drop-down choice titled 'MRT Calculations' in the Appendix B section. 

   • Now when creating a new case, users will only have 'AST Floor MRT Calculations' as a selectable option. 

Crossings Workflow 

Bug Fixes 

1. Fixed an issue in Crossings Workflow where 'Include Interpolation Method (for Influence Coefficient)' was not calculating an Ic value (TT-9556). 

   • This occurred for calculated m/n Influence factor values such that either m or n was an existing table value. 

PLTB-G      

Bug Fixes 

1. Fixed an issue in Track Load Analysis (Gas) where 'Include Interpolation Method (for Influence Coefficient)' was not calculating an Ic value (TT-9556). 

   • This occurred for calculated m/n Influence factor values such that either m or n was an existing table value. 

PLTB-L      

Bug Fixes 

1. Fixed an issue in Track Load Analysis (Liquid) where 'Include Interpolation Method (for Influence Coefficient)' was not calculating an Ic value (TT-9556). 

   • This occurred for calculated m/n Influence factor values such that either m or n was an existing table value. 

Title: Production Scheduled Maintenance - Release Notes  

Version: C-2022.12.09  

API Toolbox 

API 653 

Bug Fixes 

1. Fixed an issue in the Report Config Appendix 653 widget where user data saved in Floor MRT Evaluation would not be generated in the report. 

   • Previously, a user would create a report in the Floor MRT Evaluation, save it and, configure the drop-down in Appendix B to include MRT Calculations. 

   • Generating the final report however would not show the MRT Calculations in the appendix. 

Crossings Workflow 

Bug Fixes 

1. Fixed the following issues in Crossings Workflow that occurred on creation of a new case (TT-9480): 

   • If a Wheel or Track Load Analysis was included, ‘Depth of Cover’ was defaulting to 6.667 ft. 

   • Changing the ‘Soil Type’ drop-down to a value besides the default value ‘Granular Materials without Cohesion’ was reverting back after hitting ‘Calculate’.   

PLTB-G      

Enhancements 

1. PLTB-G reports in the following modules have been enhanced with a new template: 

   • Meters & Regulators 

   • Pipe Blast 

   • Pipeline Corrosion 

   • Input fields are now grouped into common tables such as: 

     • Pipe Description  

     • Operational Parameters 

     • Fluid Properties 

     • Results 

   • Results that are highlighted in the widget (e.g. Pass or Fail) are now highlighted on the report. 

   • If a widget has a plot, it is now included on the report 

   • Widgets with “Reduced Wall Thickness” entered by the user now have a specific note added. 

Bug Fixes 

1. Fixed the following issues in PLTB-G reports: 

   • Input and Results fields in Cathodic Protection reports were being displayed in decimal precision that did not match the widget. 

   • HDD Lite PE Pipe > Pull Force & Installation Stresses report was unable to be generated (TT-9531,TT-9536). 

   • API 1102 – Pipeline Crossing Highway (Gas) Results table had extra fluid properties rows in it. 

   • API 1102 – Pipeline Crossing Railroad (Gas) Results table had extra fluid properties rows in it. 

   • The title of ‘Total Longitudinal Stress @ MOP’ in the Results table for CEPA Crossings widgets was updated to ‘Total Longitudinal Stress at MOP’ to be consistent with titles of results fields in the widget. 

PLTB-L      

Enhancements 

1. PLTB-L reports in the following modules have been enhanced with a new template: 

   • Pipe Blast 

   • Pipeline Corrosion 

   • Input fields are now grouped into common tables such as: 

     • Pipe Description  

     • Operational Parameters 

     • Fluid Properties 

     • Results 

   • Results that are highlighted in the widget (e.g. Pass or Fail) are now highlighted on the report. 

   • If a widget has a plot, it is now included on the report 

   • Widgets with “Reduced Wall Thickness” entered by the user now have a specific note added. 

Bug Fixes 

1. Fixed the following issues in PLTB-G reports: 

   • Input and Results fields in Cathodic Protection reports were being displayed in decimal precision that did not match the widget. 

   • HDD Lite PE Pipe > Pull Force & Installation Stresses report was unable to be generated (TT-9531,TT-9536). 

   • API 1102 – Pipeline Crossing Highway (Gas) Results table had extra blank fluid properties rows in it. 

   • API 1102 – Pipeline Crossing Railroad (Gas) Results table had extra blank fluid properties rows in it. 

   • The title of ‘Total Longitudinal Stress @ MOP’ in the Results table for CEPA Crossings widgets was updated to ‘Total Longitudinal Stress at MOP’ to be consistent with titles of results fields in the widget. 

Title: Production Scheduled Maintenance - Release Notes 

Version: C-2022.09.16 

HUB^PL Platform 

Bug Fixes 

1. Fixed an issue where a user was able to modify their ‘First Name’ and ‘Last Name’ in the Preferences menu (TT-8374).  

AC Mitigation 

AC Mitigation PowerTool 

Bug Fixes 

1. The following issues were fixed in AC Mitigation PowerTool Fault Current:

   • Fixed an issue in AC Mitigation PowerTool Fault Current where vertical lines on Output > Individual sub-tab would not disappear if a user unchecked the ‘Section’ checkbox (TT-8796, TT-8853). 

   • Fixed an issue in AC Mitigation PowerTool Fault Current where the voltage values were not refreshing when TLineNo was changed accessing the Power Line drop-down (TT-8590, T-8874).

2. The following issues were fixed in AC Mitigation PowerTool Steady State:

   • The y-axis units for current density in reports was incorrectly labelled as ‘amp’ instead of ‘amp/m2’. (TT-8590, TT-8869). 

   • An extra Metric conversion factor was applied to the Pipeline Depth data after switching the widget units to Metric and exporting (TT-8796).

AC Mitigation Toolbox 

Bug Fixes 

1. Fixed an issue in AC Mitigation Toolbox Steady State where the y-axis units for current density in reports was incorrectly labelled as ‘amp’ instead of ‘amp/m2’ (TT-8590, TT-8869). 

AC Mitigation Workflow 

Bug Fixes 

1. Fixed an issue in AC Mitigation Workflow Steady State where the y-axis units for current density in reports was incorrectly labelled as ‘amp’ instead of ‘amp/m2’ (TT-8590, TT-8869). 

API Inspectors Toolbox   

API 570 

Bug Fixes 

1. Fixed an error in the Pipe CML Record widget where users were unable to specify ‘Reducer’ as a pipe description option in the ‘Comp Desc’ drop-down on each CML record (TT-8899). 

API 653 

Bug Fixes 

1. Fixed an issue in the AST Venting Evaluation report where a field in the ‘Emergency Venting Requirements’ section of the report incorrectly said ‘Tank roof attached with frangible joint?’ instead of ‘Tank roof attached with flangible joint?’.

2. Fixed an issue in APP F Evaluation report where the field unit label and values were being printed in US units when the widget units setting was set to Metric.

3. Fixed an issue in the App F Evaluation report where the title of section F.4.3 incorrectly said ‘F.4.3 -  MAWP limits based on Frangible Joint’ instead of ‘F.4.3 – MAWP limits based on Flangible Joint’.

4. Fixed an issue in the report for the Seal Inspection widget where the units label for the ‘Sum/Dia’ field would incorrectly show ‘Sq. In/ft’ when the widget settings were set to Metric.

5. Fixed an issue where “tmin” was displaying an incorrect value on the Tank Shell Minimum Thickness and Remaining Life Calculations Report (TT-7816, TT-8875)

6. Fixed an issue where Shell Remaining Life Calculations Report displayed incorrect FHc formula (TT-7816, T-8876)

7. The following issues were fixed in the Shell Settlement report when the widget unit setting was set to Metric:

   • ‘Smax’ value was displayed incorrectly in US units (TT-7816, TT-8877).

   • Formulae symbol definitions were incorrectly labelling the units system in US units.

   • ‘R^2’ calculated value was incorrectly showing US field value.

Crossings Workflow 

Bug Fixes 

1. Fixed an issue where the following input fields were not converting from US values to Metric values when the widget unit setting was set to Metric from US units (TT-9111). 

   • Weight per Unit of Backfill 

   • Modules of Elasticity of the Top Layers 

   • Modulus of Elasticity of the Soil Cover 

PLTB-G     

Enhancements

1. Added centimeter (cm) as one of the available units to the following widget calculation fields in Track Load Analysis (Gas) (TT-5692):

   • ‘B - Trench Width’

   • ‘H - Vertical Depth of Cover’

2. Added centimeter (cm) as one of the available units to the following widget calculation fields in Wheel Load Analysis (Gas) (TT-5692):

   • ‘B - Trench Width’

   • ‘H2 Depth of Soil Cover’

Bug Fixes 

1. Fixed an issue where ‘Resistance to Earth of Multiple Horizontal Anodes (Gas)’ was incorrectly titled as ‘Resistance to Earth of a Multiple Vertical Anodes (Gas)’. 

2. Fixed an issue where ‘Resistance to Earth of Multiple Vertical Anodes (Gas)’ was incorrectly titled as ‘Resistance to Earth of a Multiple Vertical Anodes (Gas)’. 

3. Fixed an issue in Track Load Analysis (Gas) where the following input fields were not converting from US values to Metric values when the widget unit setting was set to Metric from US units (TT-9056). 

   1. Weight per Unit of Backfill

4. Fixed an issue in Wheel Load Analysis (Gas) where the following input fields were not converting from US values to Metric values when the widget unit setting was set to Metric from US units (TT-9058). 

   • Weight per Unit of Backfill 

   • Modules of Elasticity of the Top Layers 

   • Modulus of Elasticity of the Soil Cover 

5. Fixed an issue in API 1102 – Pipeline Crossing Railroad (Gas) where the widget was missing calculation validation checks on the following input fields in line with API 1102 (TT-8336):

   • Operating Pressure

   • Operating Temperature

   • Outside Diameter

   • Wall Thickness

   • SMYS

   • Pipe Depth

   • Bored Diameter

   • Installation Temperature 

6. Fixed an issue in API 1102 – Pipeline Crossing Highway (Gas) where the widget was missing calculation validation checks on the following input fields in line with API 1102 (TT-8932):

   • Operating Pressure

   • Operating Temperature

   • Outside Diameter

   • Wall Thickness

   • SMYS

   • Pipe Depth

   • Bored Diameter

   • Installation Temperature 

PLTB-L      

Enhancements

1. Added centimeter (cm) as one of the available units to the following widget calculation fields in Track Load Analysis (Liquid) (TT-5692):

   • ‘B - Trench Width’

   • ‘H - Vertical Depth of Cover’

2. Added centimeter (cm) as one of the available units to the following widget calculation fields in Wheel Load Analysis (Liquid) (TT-5692):

   • ‘B - Trench Width’

   • ‘H2 Depth of Soil Cover’

Bug Fixes 

1. Fixed an issue where ‘Resistance to Earth of Multiple Horizontal Anodes (Liquid)’ was incorrectly titled as ‘Resistance to Earth of a Multiple Vertical Anodes (Liquid)’. 

2. Fixed an issue where ‘Resistance to Earth of Multiple Vertical Anodes (Liquid)’ was incorrectly titled as ‘Resistance to Earth of a Multiple Vertical Anodes (Liquid)’. 

3. The following issues were fixed in API 1102 – Pipeline Crossing Highway (Liquid):

   • A user would receive a validation message for minimum required wall thickness that incorrectly referenced CFR 192 instead of 49 CFR 195.106 (TT-6867). 

     • Previously, when a user’s pipe wall thickness was less than the minimum required wall thickness, the message would be received after hitting ‘Calculate’: “Insufficient pipe wall thickness for given operating conditions. In accordance with CFR 192, “minimum required wall thickness” should be greater than ….”. 

   • The widget would incorrectly display the ‘Location Class’ drop-down (TT-6844, TT-8994). 

   • The ‘Design Factor’ field was not defaulted to 0.72 in line with API 1102 (TT-6844). 

   • The widget was missing calculation validation checks on the following input fields in line with API 1102 (TT-8932):

     • Operating Pressure

     • Operating Temperature

     • Outside Diameter

     • Wall Thickness

     • SMYS

     • Pipe Depth

     • Bored Diameter

     • Installation Temperature

4. The following issues were fixed in API 1102 – Pipeline Crossing Railroad (Liquid):

   • A validation message to the user for minimum required wall thickness was missing (TT-6867). 

   • The widget would incorrectly display the ‘Location Class’ drop-down (TT-6844, TT-8994). 

   • The ‘Design Factor’ field was not defaulted to 0.72 in line with API 1102 (TT-6844). 

   • The widget was missing calculation validation checks on the following input fields in line with API 1102 (TT-8336):

     • Operating Pressure

     • Operating Temperature

     • Outside Diameter

     • Wall Thickness

     • SMYS

     • Pipe Depth

     • Bored Diameter

     • Installation Temperature

5. Fixed an issue in Track Load Analysis (Liquid) where the following input fields were not converting from US values to Metric values when the widget unit setting was set to Metric from US units (TT-9056). 

   • Weight per Unit of Backfill 

6. Fixed an issue in Wheel Load Analysis (Liquid) where the following input fields were not converting from US values to Metric values when the widget unit setting was set to Metric from US units (TT-9058). 

   • Weight per Unit of Backfill 

   • Modules of Elasticity of the Top Layers 

   • Modulus of Elasticity of the Soil Cover 

PRCI Thermal Analysis       

Bug Fixes 

1. Fixed an issue where users selected carbon steel pipe data, but the generated report displayed duplex stainless steel as pipe material. (TT-8792)

Title: Production Scheduled Maintenance - Release Notes

Version: A-2022.08.12

HUB^PL Platform

Enhancements

1. Implemented the following performance enhancements (TT-8652):

   1. Reduced the timeout of the “Please Wait” loading wheel onscreen.

   2. Implemented data caching.

   3. Implemented data on demand for rendering.

2. Added password controls to HUB^PL user passwords that now consist of:

   1. Passwords are required to have a minimum of 16 characters.

   2. Passwords are required to have one of each of the following:

      1. Special symbols

      2. Upper case

      3. Lower case

      4. Numbers

   3. A user will be locked out of their account if there are 3 invalid login attempts.

   4. Passwords cannot be the same as any of the previous 5.

3. The Notifications widget has been restored to the application and a URL to the external release notes Confluence site has been added inside this widget.

Bug Fixes

1. Fixed an issue where users were unable to access the TTI Support Wiki from the Support menu (TT-8901).

AC Mitigation

AC Mitigation PowerTool

Enhancements

1. Added Save validation to AC Mitigation PowerTool Steady State and Fault Current to inform the user of being unable to save if no Pipelines or Powerlines are configured in their case.

2. Added Pipelines, Powerlines, Sections, and Mitigation input to Steady State and Fault Current reports (TT-6836).

3. Added ability to name and save Powerlines and Pipelines (TT-7030).

Bug Fixes

1. Fixed an error in Fault Current where Pipeline Length Depth values weren’t updating after hitting Calculate on the widget; this would affect Excel exports and reports generated (TT-8854).

API Inspectors Toolbox

API 510

Bug Fixes

1. The following errors were fixed in the API-510 Inspection and Evaluation widget:

   1. Clicking on a new subpage wasn’t going automatically to the top of the page.

   2. The latest revision codes were missing.

2. The following errors were fixed in the API 510 Report Builder:

   1. PDF reports had names in coming in with the format ‘reportname_xxxx’; the ‘_xxxx’ characters have been removed from the downloaded report name.

   2. Calculations were not functioning properly.

   3. Copying of reports was not bringing in Logo or Company Name data into PDF reports.

   4. The Report Appendix widget was missing the value below for the ‘Extraneous Calculations’ pull down:

      1. Flanges – App 2 Calcs

      2. Expansion Joints

      3. MDMT Eval

      4. Patches

   5. The Executive Summary wasn’t properly indenting in the first paragraph.

3. Fixed an error where there was white space on the Horizontal Tank Evaluation widget; the ‘Stiffening Ring(s) Installed?’ and associated drop-down have been placed next to the ‘K8’ cell.

4. Fixed an error in the Hydro Testing widget where the Pressure Test Records menudisplayed a drop-down menu for all file test records instead of displaying the record associated with the file in the widget.

5. Fixed an issue in the Floating Cover widget where printing a report after choosing ‘Shellside Calculations’ would incorrectly put ‘Exchanger Floating Head Cover TS Calculations’ instead of ‘Exchanger Floating Head Cover SS Calculations’.

6. The following issues were fixed for the Formed Head widget:

   1. Running a PDF report of a Hemispherical calculation was causing the variable ‘Ro’ to not be printed to 3 decimal places.

   2. Running a PDF report of an Ellipsoidal calculation was causing data to be missing in the first box.

   3. Running a PDF report of a Torispherical calculation was causing the following:

      1. The variable ‘r’ being incorrectly printed as ‘R’.

      2. The variable ‘M’ having incorrect formatting. 

   4. Running a PDF report of a Torispherical calculation was causing the 1^st box on the report to be missing data.

   5. Titles of input fields weren’t aligned over the center of the input field.

      1. E.g. The variable ‘B’ would appear to the left of the input field instead of over it aligned to the center.

   6. The positioning of the variable ‘B’ wasn’t aligned over the center of the input field.

   7. Running a PDF report was causing the ‘SH’ field to show as empty in the report if the user entered ‘0’.

7. Fixed an issue in Material Spec where generating a report with ‘Print Individual Spec’ was not generating the Material Grade value at the top of the 2^nd page.

8. Fixed an issue in the MDMT PDF report where the variable ‘tr’ was being printed beyond 3 decimal places of precision.

9. The following issues have been resolved for widgets under Weld Procedure Evaluation:

   1. The Procedure Qualification GTAW QW-256 widget was incorrectly showing SAW information.

   2. The Procedure Qualification GMAW / FCAW QW-255 widget was incorrectly showing SAW information.

10. The following issues were fixed in the Welder WPQ Evaluation widget:

    1. The ‘ASME Sec IX’ button has been removed.

    2. The ‘Print’ button has been fixed to support Word and PDF exports.

    3. The ‘Welder Variables’ button has been fixed.

    4. The ‘Notes’ buttons on each row have been fixed.

11. Fixed an error in the PV Component Remaining Life Calculations widget where values for ‘Shell 1’ and ‘Head 3’ were being interchanged.

12. The following issues were fixed in the PV Inspection Forms widget:

    1. The PV Boiler Plate Dwg. Horz. report had incorrect formatting.

    2. The PV Boiler Plate Dwg. Vert report had incorrect formatting.

    3. The drawing in the 2^nd page of the PV Boiler Plate Dwg Horz. report had an incorrect horizontal tank template.

    4. The Pressure Test Form and MFE reports comments sections were not left justified.

13. The following issues were fixed in the Reinforcement Pads widget:

    1. White space between ‘Element Groove Weld?’ text and drop-down to its right under ‘Weld Loads and Strength Paths’ section has been corrected.

    2. ‘Path 3-3’ field under ‘Strength Path Check’ section has been corrected to show the calculation result as a whole number.

14. Fixed an error in the Shell Calcs widget where running a PDF report was causing the ‘SH’ field to show as empty in the report if the user entered ‘0’.

API 570

Bug Fixes

1. The following issues were fixed in the API-570 Inspection and Evaluation widget:

   1. Definitions and April 2018 Errata 1 weren’t up to date.

   2. Information in Piping Inspection sub-tab needed updates to inspection code info.

   3. Switching between tabulated windows wasn’t correctly starting at the top of each page.

2. Fixed an issue in the API 570 Report Builder where downloaded reports were coming in with the format ‘reportname_xxxx’; the ‘_xxxx’ characters have been removed from the downloaded report name.

3. Fixed an error in Bolting Specifications where data points displayed in ft/lbs weren’t being displayed as whole numbers; these data points were the following:

   1. Trq 30k

   2. Trq 45k

   3. Trq 60k

   4. 30k Cmp

   5. 45k Cmp

   6. 60k Cmp

4. Fixed an issue in Conversion widget’s ‘Volume, Dry’ section where ‘bushels, IMP’ had incorrect values calculated from the input by the user.

   1. E.g. If the user put in 1 cu ins, ‘bushels, IMP’ would be incorrectly calculated to 0.00052 IMP and 0.00054 bushels US. The correct conversion for either should've been 0.0005243 bushels IMP and 0.0005411 bushels US respectively.

5. Fixed an error in CS Pipe Sizes where data in API Standard Line Pipe section where data was being shown incorrectly at 3 decimal places of precision.

   1. Decimal precision of data in this section has been updated to 1 decimal place.

API 653

Bug Fixes

1. Fixed an error in the Component Remaining Life Calculation report when using Metric units where incorrect values for tprev and tact were being used in the calculation of remaining life (RL) (TT-7816).

2. Fixed an issue in APP F Evaluation where the 'See Moment Values' window was not appearing when clicked (TT-8750).

Crossings Workflow

Bug Fixes

1. Fixed an issue where a user was unable to input Pipe Characteristics and Equipment Characteristics when creating a new case. Previously, these sections would appear blank when a new case was created (TT-8953, TT-9005).

Encroachment Manager

Bug Fixes

1. Fixed an issue where creating a new encroachment prevented users from saving unless they configured a pipeline.

HDD PowerTool       

Bug Fixes

1. Fixed an issue where plots were not generating (TT-8927).

PLTB-G    

Bug Fixes

1. Fixed an issue Reinforcement of Welded Branched Connection – ASME B31.8 where Provided Area (AP) > Required Area (A3) was incorrectly calculating the branch connection as ‘NOT ACCEPTABLE’ (TT-8435).

PLTB-L     

Bug Fixes

1. Fixed an issue Reinforcement of Welded Branch Connection – ASME B31.4 where the widget name was incorrectly titled ‘Reinforcement of Welded Branch Connection – ASME B31.8’ and the report incorrectly referenced ‘ASME B31.8 and 49 CFR’ (TT-8958).

   1. This error also caused the Excel export to have an incorrect title of ‘Reinforcement of Welded Branch Connection – ASME B31.8’

Title: Production Scheduled Maintenance - Release Notes

Version: C-2022.05.27

HUBPL Platform

Enhancements

• Implemented a new functionality where the user can now delete logos in preferences.

Bug Fixes

• Fixed an issue where the Pipe Catalog data had incorrect outside diameter and wall thickness values in the dropdown.

• Fixed an issue where the reports were not generated across all modules in HUBPL if a logo was not uploaded in the preferences section (TT-8324).

• Identified an issue not supported in HUBPL and updated the same in TTI Support Wiki for KML/KMZ files that is not supported by our ESRI solution when one single layer contains multiple features.

• Fixed an issue where Data Availability would not load any data upon selection due to a loading error.

• Fixed an issue where Ad-hoc - Company data (shared entity and case data) was not plotting.

AC Mitigation PowerTool

Bug Fixes

• Fixed an issue where the powerline info table listed a maximum of 10 powerlines even though the number of powerlines configured was beyond 10 in the Google map version (TT-8745).

• Fixed an issue where the powerline data was not loading in old steady state cases.           

AC Mitigation Workflow

Bug Fixes

• Fixed an issue where the users could not add pipes/power lines from hierarchy and map.              

• Fixed an issue where the steady state case was not displaying results when calculate was clicked.              

AC Mitigation Toolbox

Bug Fixes

• Fixed an issue where the Fault Current module was not loading as expected, which was restricting the users from entering data in order to analyze a case.    

Pipeline Crossing Workflow

Bug Fixes

• Fixed an issue where the number of reports generated was incorrect and usually less than the cases configured (TT-8288, TT-8610).

Hydrotest PowerTool

Bug Fixes

• Fixed an issue where the tool tip needed grammar correction from "Is" to "Are" when hovered over “Are there any Components included in the Hydrotest.”

API Inspectors Toolbox

API 510

Bug Fixes

• Fixed an issue related to loading widgets when new files were created and saved on user choice of the metric unit set.

  • Previously, the wait/load time was large and when loading was complete, not all columns would properly display data.

• Fixed an issue in Horizonal Tank Calculation where 1st Box, Variables K1 & K8 are incorrect for Stiffened Shell, and should default to a value of 3.14 when selecting Stiffing Ring Installed at the very bottom Orig.           

• Renamed label to Tower Loads in Loads (Wind, Press, Wt).

• The following issues were fixed in the Tower Piping Work Sheet:

  • The existing definition field has been updated with the original definitions from references.         

  • The missing 2nd block has been added to PDF Reports.    

  • The shear value used in calculations in this sheet has been corrected.     

  • The M3 value has been placed on the sheet.

  • The Mt value has been corrected.            

  • On the bottom of the 1st page of the PDF report, the stress due to wind value has been corrected from the "Yes" value that was given before.   

• Fixed an issue where APP A Table (top right) was not recording the lowest reading when one CML row was empty and would not let users delete from Table cell, which should be editable and only filled when closing the CML Data Input record.         

• Fixed an issue in APP A which is coming without the applicable box checked. When putting a check into it duplicates subject (identical) with some PDF docs.           

• Fixed an issue in APP A where building the CML records and inputting the data caused a significant slowing of the process.

• Fixed an issue in APP B – Flange Calculation where in ASME Sect VIII, Div 1, APP 2, several Factors were incorrect:

  • “y” variable was coming in with a default value but should have been empty.

  • “Ca” value was not retaining “0” value when exiting.

• Fixed an issue in APP B Formed Head calculation where the tmin value could be less than 0.063.

• Fixed an issue in APP B – Report Formed Head Calcs where the next inspection (Yn) has an incorrect value for inspection with < ½ life remaining.

• The following issues were fixed for APP B – Report Nozzle Calculation:

  • The calculation at the bottom - E, P, OD, & User Defined tmin user overrides were not holding, and the t value was not being used in the tmin algorithm.

  • Incorrect stress values resulted in incorrect tmin.

  • Calculations were coming in at the very bottom and needed to be moved up to ¾ of the view to track the individual CML points.

• Fixed an issue in APP B Non-Round Flat Cover where the PDF report was not printing the welded report, instead it printed only the bolted report even when “Welded” was selected for the print status.

  • Wm1 & Wm2 need to be integers.          

• Fixed an issue in APP B – API-510 Remaining Life where, if External was selected for “Inspection Type,” the Next Inspection - Internal cell should display “NA."          

• Fixed an issue in APP B – Report Shell Calcs & Report Formed Heads Calcs where Ca & RL showed false values when the tprev and tact had no values to calculate those variables.

• Fixed an issue in APP B Shell Calculation/Simple & Complex Vessel where the REMAINING LIFE AND NEXT INSPECTION DUE DATES – Vessel Shell & Jacket head were showing false values when all the variables are not entered. When all variables are not entered, these should be blank.

• Fixed an issue in APP B – Tube Sheets Calculation where the button [Gasket Data (y,m,G,b)] – G value was incorrect. G value in the PDF report must be corrected to 3rd decimal.    

• Fixed an issue in PV Nozzle Evaluation where Ca and Cr Values were not populating data.

• Fixed an issue in PV Report Print – where print report no. was incorrect, Horz Calcs - Tangential Shear Stress/Sum of Stress in Head / Ratio limit to 3rd decimal and stress value is corrected.

• Fixed an issue in the final report with Complex Vessel where Table A had incorrect tmin & RL values.        

• Fixed an issue in the full PDF report that resulted in it not displaying remaining life if 0 years was selected in some components.        

• Fixed an issue in BASE 1 Material 7Cr 1/2Mo, 90 Cu-10Ni_70 Cu-30Ni, 9Cr 1/2Mo, Alloy 1100_3003, Alloy 5052, C_Mn (>70K), C_Mn (to 70K), Carpenter 20 Cb3, Hastelloy B2, Hastelloy C276, Hastelloy C4, Incoloy 800_825, Incoloy 801_802. All Preferred Gases were incorrect and/or missing some data.

• Fixed an issue in BASE 1 Materials - 2_2 25Cr 1/2 1Mo,  C_Mo, 304 (> 1000F), 304 (to 1000F), 304L, 309, 310, 310Cb, 310Mo, 316, 316L, 317, 317L, 321_347, 405_409, 410, 410S, 430, 5Cr 1/2Mo, to Preferred Gas Material missing value. 

• Fixed an issue in Preferred Gas where full descriptions could not be displayed.

• Fixed an issue in Floating Cover where the flange allowable Stress, Sfo, Sbo, & Sho values for both 98 and 00 values were incorrect. They should be based on the greater temperature between T-SS & T-TS.  

• Fixed an issue in Floating Cover where the TS Calculation “Flange t Req w/ Ca” had incorrect values in the PDF report (Corresponding to “Flange Design t min” in form).              

• The following issues were fixed in Nozzle Reinforcement:

  • The middle evaluation (for the repad) A41 had incorrect values which resulted in an incorrect calculation.

  • The Elem Groove Weld tension (Tegw & STegw) & Noz Groove Weld tension (Tngw & STngw) should not have been calculating when “No” was selected for “Elem Groove Weld?” & “Noz Groove Weld?” should have “0” in their cells.     

•  Fixed an issue in Tubes where the differential pressure cell was empty in the report when “0” was entered on the UI.